VViViD3M Clear Paint Protection Vinyl Film 12" Wide Choose Your Size Including Tools (12" x 6")

This film was really easy to apply with a spray bottle of water and a good quality flexible squeegee (make sure to use distilled or reverse osmosis water to avoid hard water residue). The material was easy to conform to the compound curve of my motorcycle gas tank. Also there was enough stretch that I could peel up and reposition the sheet easily. It looks much more discreet than an adhesive tank pad, almost impossible to see the film except in direct sunlight. The edges have not peeled up in hot weather or when washing the bike. A little expensive for the amount of material, but it’s worth it for the quality product. For the front of the whole bike or a car, probably more economical to go to a shop. But definitely recommended for discreet protection of relatively small areas like the back part of the tank or the side panels you always hit with your boot. Probably very useful for scratch protection around the house too. Recommended.

headlights look like new again

I'm sure it's a fine product and works well with a proper installation, but I had no luck getting this to work right on my headlights. If you don't have the patience for doing things that are tedious and frustrating, this is not for you and I recommend having a professional install it. It would be easy to placed on lights that are mostly flat and rectangular, but modem car headlights with more complex shapes are significantly more challenging to wrap without getting several wrinkles and air pockets. My headlights have a sharp crease line in them that made it almost impossible to stretch over. Even with heat applied and numerous reapplications with wet film, it simply would not adhere smoothly and I had to give up. My headlights are also very large and took 99% of the roll to completely cover and even then the width is only barely wide enough for them - this leaves NO room for mistakes. And mistakes are easy when you're working with a giant curled up rectangle of adhesive vinyl... this stuff wants to curl and stick to itself constantly and it's hard to peel apart again. If you're working with huge pieces like I had to, I almost recommend having a second person to hold the other end of the sheet for you so it can stretch from all 4 corners. That might make applying it easier too. I don't want to knock the product itself too much because I can tell it's high quality vinyl. The parts that did stick properly were nice and clear and it was easy to squeegee out the moisture. I recommend buying a softer silicone or rubber squeegee though, as the provided plastic one seems really sharp. Overall, this is not a simple product to install if you have complex headlights. It takes a ton of patience, some handy skills, and extreme delicacy to do it right. I'm not really sure it's worth the frustration for a few years of protection that a good spray-on clear coat might be able to compete with.

I purchased this to supplement the purchase of another 3M paint protection vinyl product; a pre-cut body panel kit for a recently purchased 2017 dually pickup. The leading edge of dually fenders really get banged up with rocks, so I wanted the paint protected before I racked up too many miles. I used this 12" universal roll to fill in the gaps that the pre-cut kit didn't cover, including going all the way down to the bottom of the fender. To do a good job, this product requires a lot of patience, and the need to use home-made application mixtures per the instructions. I ended up with some bubbles, which is hard to avoid, but with a syringe, was able to remove the air pockets so the clear film would lay flat. After several hours of work, including thoroughly cleaning the surface, the final results are excellent. Virtually invisible, and will prevent the fenders from getting those ugly chips for a long time. This is a high quality product.

BUEN PRODUCTO

Unfortunately the roll of product I received had a masking tape material left attached and still taped onto the clear vinyl film from which I could only assume was the manufacturing and or sizing/cutting process which caused the product to yellow where the tape had not been removed prior to final packaging.I purchased this vinyl for vehicle use, so ultimately I ended up with clearly visible yellow streaks showing up in my installed clear layer of protective film. (Quality control issue.. as previous identical item purchase a couple years ago did not have this issue, so maybe only some rolls are affected).

I damaged a fender on my dually pickup. When I had it repaired, the body shop wanted over $100 to purchase and install the factory stone guard panel. I purchased the 3M material and made a paper template from the undamaged stone guard on the opposite fender. I flipped the template and traced it onto the 3M film so it would be the correct shape. I waited a few weeks for the paint to cure, thoroughly cleaned the area of the fender with soap, rinsed, then cleaned with alcohol. Used a baby shampoo spray solution for application. Took maybe 5 minutes to clean, prep, position and squeegee. Still looks great (can hardly tell it is there) several months later. This was a much cheaper solution.

Repackaged and Missing VViViD Toolkit: Yellow Detailer Squeegee and 2 Anti-Scratch VViViD Felt Decals