SpyderAuto PRO-YD-DR02-HL-BK Dodge Ram 1500/2500/3500 Black Halogen LED Projector Headlight

The Good: Awesome looking head lights. The low beams light up the road like it's nobody's business. The high beams are great.The Bad: Lights are built in to the unit. Turn signal mount on one side is a little iffy. LED Halos are not as bright as I'd like.The Ugly: Wiring everything. It's a bird's nest. but its pretty cool. Aiming the lights. I've heard of people pulling the inner fender, you don't have to do that. Insert the light, and tighten the top bolt, leaving the bottom bolt out. It's time consuming, but it's easier than tearing the inner fender out.All in a short: Worth the money, ten times better than the factory lights, and they look cool. If you've got basic electrical knowledge, this isn't hard to do.

Good product. Easy replacement option for factory headlights. My originals were fogged and had been cleaned several times. They were never as bright as I wanted. These are a good replacementent option that are significantly brighter than the originals, but still not as bright as I would like. Install is straightforward and easy. As some others noted, adjusting the beam pattern is not as easy, requiring the removal of the light to adjust bolts/nuts on the rear. This requires installing, checking, pulling to adjust, reinstalling, repeat to get the beam properly adjusted. Though it takes a while, once it is adjusted, you are done and should never have to deal with that again.

Dislikes first...the stock light connectors in my Dodge ram didn't fit this lights housing for turn signals...I ended up finding the right connectors and if anyone has the same issue you'll need to pick up the Chrysler turn signal bulb connector sockets available on rockauto if you want to use these lights. They're a tan pink color and have the Chrysler logo stamped on them. That solves that issue...also before you leave these lights after install you may want to pick up a few zip ties or elect. tape and make a harness binder because the wires tend to hang out the bottom of the mount area after installation and you wanna protect those a bit more from the elements. The lights look amazing and the led lights look great. Good clarity and road illumination and a great fit on my truck. Better than the original headlights that came on the truck. Would I buy these again? I would..but I would go upgrade even higher to another version of the halo Spyder makes..I like these alot the black backing makes the light blend in well...I would still upgrade higher to thier more expensive light for my truck. That may be something I do after these wear out. Here's the big idea..you want to have these lights covered. Getting a wrap cover will protect these lights for years and help them stay scratch and fade free. It runs on the high end about $350 to wrap your lights and it isn't as easy as just sticking some tint to them. It's not super hard but it's not worth making a mistake that decreases the life of your lights. But...they're still good lights to run out of the box...throwem in and drivem till they fall out. It's not gonna cure your bad breath or grow hair on your chest either way. They're just lights. Worth the upkeep but still just a requirement for driving. Thanks

****update right low beam burnt out****After only a couple months I no longer have a right low beam. I will update if it is an easy fix or if I have to go through customer service. 4stars to 3Lights seem to be a good enough quality. They aren't as bright as I hoped but a definite improvement over stock. The install was not as overly difficult but time consuming. A lessened learned on my 04 dodge 2500 If you aren't getting 12v on your park lamp line (for the led halo accessory) make sure you double check your fuses (a hair line crack added an hour of trouble shooting). These lights only get 4 stars from me because the adjustment system to aim them is garbage and lacks a true left right up down (both adjust both directions off the same bolt.) Over all an improvement but I would have paid extra $$ to be able to adjust them without removing.

The lights are awesome spiffing up my old truck. I just have to angle them correctly with rubber spacers to get the light distance right. I have yet to do this. The turn signal/ parking light socket is terribly matched up. I had to cut away the notches in the socket to fit the headlight. The LED light are about to be installed with male/ female connectors for simplicity. I'll add a photo later to show my work.

These lights are beautiful. They are very high quality, the fitment is perfect. Either on or off, they change the looks of the truck dramatically.Now now the not so good. They are not plug and play. In order to save a few bucks, the manufacturer did not see fit to include the parking/turn socket. Therefore, the LED's and the halos are not prewired. It is necessary to break into the parking light circuit to connect the LED's and the halos. First the parking light circuit has to be identified. To do this, there must be a bulb plugged into the circuit. The ECM puts a tickler voltage on both circuits of the lamp for the lamp monitor function. Very carefully make the connections. This is an area that is exposed to violent splashing of water. So it has to be perfect. Use shrink tubing!I feel that any headlight assembly that requires the inner fender be removed to adjust them after installation should be mentioned in BIG LETTERS in the description. That's why 3 starsBut they ARE real good lookin'!

This is short term. I am not commenting on long term. I installed yesterday. They are gorgeous. I got the smoke lens with chrome background. These have the perfect amount of smoke. Not too much to where it's ridiculous. They looks great. Wiring them up took me a few mins to figure out. Once you figure it out it will take about 2 hours to complete everything. They fit perfect. The instructions tell you how to adjust the headlight. I didn't adjust mine. They are good enough on the factory adjustment.

I was skeptical about buying these based on many reviews saying the turn signal connector does not fit and you could either cut it or purchase the pink Chrysler connector. I ordered them anyways and yes, the cutout did not fit my 2003 Ram 1500. The issue is they did not think of how the connector twists and the cutout is molded in a way which conflicts with other components of the light. I contacted my Chrysler dealership to find the pink turn bulb connector someone else referenced was almost $90 each (Canada). So I tried cutting it to save money. Cutting it works fine and you don't need fancy tools or know how to do it. I just used a razor knife and cut the slots to fit my connector. Lights work great and are slightly smaller than the factory lights making them easy to fit where they go. Gave 4 stars because they are not "plug and play". As for the electrical, there is no instructions but a simpleton like me did it just using a quick splice connector(s) and a multimeter.

SURE THEY LOOK GREAT BUT FORREST GUMP IS BRIGHTER THEN THESE LIGHTS!! CAN'T EVEN SEE 20 FEET IN FRONT OF MY TRUCK WITH THESE JUNK LIGHT.

I dislike the fact my marker light bulb socket had to be modified , it's not a plug and play

For the price of a product of this much adjustment of the light beam wasn’t their first choice could have been much better

Husband loves them and they look great