Tiella 800CBL5PN-LED, Accent Electronic Low Volt Surface Track Lighting Kits, LED Compatible, Nickel

We are so happy with this kit. We were able to afford the cable lighting that my husband and I hoped to have "some day". Custom assemblies and other kits are so much more pricey. We bought 2 for our kitchen. After we removed the drop ceiling, we discovered a beam that can't be removed, so we kept the soffits. The cables run between them on either side of the beam. They cast unique light/shadows on the ceiling. In time, we hope we don't have the transformer issues that some people have. Initially, I was concerned that the 20 watt bulbs might not be bright enough. Now, I prefer them. If I want a lot of light for cleaning daylight is best, but we have bright light above the sink, the eat in area and the stove. Plus, we added cabinet lighting. They look great! Installation worked well. We had only 2 issues: 1) One kit didn't include the small allen (sp?) wrench, but we had it in the other. 2) 2 of the light assemblies didn't work. We swapped out a bulb in one, so think it might be the assembly. Maybe we can get them to work, but since we only used 8 lights we didn't spend a lot of time trouble-shooting.

I bought two of these kits because I needed 10 lights. I swapped out the five 20W Halogen lights for ten 7W LED replacements. The 100 W transformer can easily handle the 70 total LED watts and the setup is dimmable. I was concerned that the 10 fixtures would make the cable sag. It does, but I found a sort of solution (below).The installation of this cable light kit can be complicated. Some examples:1) Allen wrenches - As others have said, there is a problem with the size (or sizes) of the Allen wrenches used to tighten or remove various set screws. The Instruction Manual shows two (2) small Allen wrenches included, while there are really three (3), each a different size. Make sure you have three, and use the right one. The smallest, for example, is needed to loosen and tighten the set screws to insert the light bulb posts.2) Ceiling mount 1 - The Manual shows 3 possible installation options, two of which involve mounting the posts on the ceiling. But the post without the turnbuckle does not easily accommodate a ceiling mount, as the cable is inserted into the END of the post. Fortunately, the cable is soft and bends easily – just be sure to tighten the set screws securely (using the right Allen wrench!). Note that in this installation if the cables pass over the transformer cover, they come close to but don’t touch it.3) Ceiling mount 2 - I needed to mount both ends of the cable to posts on the ceiling. This was not difficult, as I did not hit any joists above the drywall. Unfortunately, the torque on the end of the posts when the cable was tightened by the turnbuckle caused the posts to lean inwards because the drywall anchors were not solid enough to take the strain. I had to back off the tightness a bit, and that’s when the cable sagged a little.4) Sagging cable – Fortunately I had two complete kits, giving me an extra set of the posts without the turnbuckle. After removing the lowest set screw, I drilled all the way through the post there. I mounted these posts in the middle of my cable, ran the cables through the new holes and the sag was significantly reduced.5) Shortening the power cables – My installation took the cables right over the transformer cover and the foot-long power cables looked bad and needed to be shortened. Apparently, the manufacturer does not want to have the end connector removed from the power cable, as the Allen set screws seemed to have been “stripped”. None of the provided Allen wrenches would turn the set screws. My McGuyver answer was a tiny Torx screwdriver that I could force into the set screw and get it to turn. After cutting and stripping each insulated cable, I was able to reinsert the end into the connector and retighten the set screws with the Torx. Looks much better.6) Something I missed – The silver washers that are used in mounting the posts need to be put so the slight cutout faces the mounting surface. This little space accommodates the likely protrusion of the top of the drywall anchor screw, and results in a nice flat mounting.I’m quite happy with the product and my handiwork. We can now illuminate a number of African carvings we have collected but never properly displayed. By installing a series of “floating” shelves along an unused wall down a hallway, we will have not only a nice art display but also lots of light.

I had a wire track light in my kitchen that was ready to be replaced. I loved the look so much, I wanted to replace it with a similar wire track light. Surprisingly, this one was only a very few that I found, not only on here, but on a Google search. I didn't like the price. I think it was a bit overpriced but still purchased it. Result, I couldn't be happier how everything came out after remove/replace. It looks better than the original I had! It's given my kitchen a modern and elegant look. Now, much of this is due to the lamp bulbs that I got for it. Be ready, they are around $25-30 bucks each! Be sure that you follow the manufactures watts and volts for the bulbs! This is what brought my original lamp to an end. But like I mentioned before, I am very happy how everything came out and so will you! So, this wire track lamp is $220, and the five lamp bulbs came out to $130, total...$350! Yes, it is pricey, but folks, you will love the look of this lamp that has multiple applications! If you can stretch the cost, you will not be disappointed!

This is junk. The cheap transformer fails immediately, not after one of the cheap light fixtures stopped working and when I went to look why, it looks like some kind of electrical short?The fixtures themselves are beyond cheap. They hold the light with two very tiny hex screws. This means to change a light, hope that you dont misplace or loose the micro-tiny hex wrench they include which you need to loosen the micro-tiny screws.Also, there is zero customer support. I tried calling, emailing - NADA. \Now I get to uninstall it and send it back. Can not believe how horrible this is.